.INI file for the FET-3 (TurboCNC)

Dec 15

Posted by

Got TurboCNC to work with the FET-3 controller from Stepperworld.

If you need an .INI file for the FET-3.  Use the following below.

You will still need to calibrate your machine, but at least it will configure the motors.

;Ini file for TurboCNC v3.0g and above…

[General]IniDescription=TurboCNC 4.0 DistributionNumberOfAxes=3Start Inhibit=YESBlock Inhibit=YESConfiguredAsImperial=YESImperial Places=0Metric_Places=0Default_Feed=10.000000000000Home_Feed=10.000000000000ArcFactor=1.000000000000StopOnIllegalCodes=YESMonochrome=NOMouse Hide=YESLoad_Tooling=NOVerbose=YESSync Unit Indices=NOSync Axis Indices=NOListDir=c:\maxnc\belt\ListExt=.CNCToolDir=C:\TOOL\ToolExt=.TLPoint Filename=.\POINTS.DATReverseDelay(ms)=0TurretIndexTime(ms)=2000ColletOpenTime(ms)=2000ColletCloseTime(ms)=2000SpindleTime(ms)=7000RelaySettleTime(ms)=100ClampDelay=15000.000000000000MachineType=NoTypeUsePentiumTimer=NOClearMDIPrompt=NOHomeIsLimit=NOM6JogUpdateDistances=YES

[Editor]First_Block=Last_Block=M30Add_First_Block=NOAdd_Last_Block=NO

[Dialect]LinearRapids=YESG04Letter=PG04InMS=NOArcIJKMode=1G8xReleaseLetter=RG8xDwellLetter=PG8xDwellInMs=YESG8xPeckLetter=QG33IsLead=YESJump_Target=ORewindOnM30=NO

[AXIS1]Designator=XStepIncrement=0.000625000000IsLinear=TrueIsStep/Dir=TruePortAddress=$378StepPin=3IsActiveLow=TruePulsewidth=150DirPin=2LowIsPositive=TrueAcceleration=2000.000000000000StartSpeed=150.000000000000MaxSpeed=350.000000000000Fast_Jog=350.000000000000Slow_Jog=50.000000000000InvertJogKeys=NO

[AXIS2]Designator=YStepIncrement=0.000781250000IsLinear=TrueIsStep/Dir=TruePortAddress=$378StepPin=5IsActiveLow=TruePulsewidth=200DirPin=4LowIsPositive=TrueAcceleration=1500.000000000000StartSpeed=150.000000000000MaxSpeed=350.000000000000Fast_Jog=350.000000000000Slow_Jog=50.000000000000InvertJogKeys=NO

[AXIS3]Designator=ZStepIncrement=0.000952380952IsLinear=TrueIsStep/Dir=TruePortAddress=$378StepPin=7IsActiveLow=TruePulsewidth=150DirPin=6LowIsPositive=FalseAcceleration=1750.000000000000StartSpeed=500.000000000000MaxSpeed=700.000000000000Fast_Jog=500.000000000000Slow_Jog=50.000000000000InvertJogKeys=NO

[DRIVE_ENABLE_1_(OUTPUT)]Enabled=TruePin=14PortAddress=$378ActiveHigh=NO

[DRIVE_ENABLE_2_(OUTPUT)]Enabled=TruePin=16PortAddress=$378ActiveHigh=NO

[DRIVE_ENABLE_3_(OUTPUT)]Enabled=TruePin=17PortAddress=$378ActiveHigh=NO

[SPINDLE_INDEX_(INPUT)]Enabled=TruePin=12PortAddress=$378ActiveHigh=YES

[Imperial Jog]Axis 1 Index=1Axis 2 Index=1Axis 3 Index=1Jog Element 1=0.001000000000Jog Element 2=0.001000000000Jog Element 3=0.001000000000Jog Element 4=0.001000000000Jog Element 5=0.001000000000Jog Element 6=0.001000000000Jog Element 7=0.001000000000Jog Element 8=0.001000000000Jog Element 9=0.001000000000Jog Element 10=0.001000000000

[Metric Jog]Axis 1 Index=1Axis 2 Index=1Axis 3 Index=1Jog Element 1=0.010000000000Jog Element 2=0.010000000000Jog Element 3=0.010000000000Jog Element 4=0.010000000000Jog Element 5=0.010000000000Jog Element 6=0.010000000000Jog Element 7=0.010000000000Jog Element 8=0.010000000000Jog Element 9=0.010000000000Jog Element 10=0.010000000000

[Persistent]Halt_On_M01=NOExecute_Slash=YESShow_Backlash=YESJog Mode=YESWorkInImperialSystem=YES

[POSITION]1=0.3750000000002=-50.6656250000473=0.000000000000

[LASTBACKLASH]1=12=-13=0

[Speed_Map]
Advertisement

About mattsanf

Matthew Sanfilippo is currently Executive Director of PSII (Pennsylvania Smart Infrastructure Incubator) and the CenSCIR (Center for Sensed Critical Infrastructure), Associate Director of ICES (Institute for Complex Engineered Systems), and Associate Director of PITA (Pennsylvania Infrastructure Technology Alliance) at Carnegie Mellon University (CMU). Prior to CMU, Matthew was Director of Applied Technology for Michael Baker Corporation, a large engineering and energy services firm. Matt managed a technology consulting division for Baker including Geographic Information System (GIS), software and web development, multimedia, virtual reality (VR), visualization, Global Positioning System (GPS), mapping and surveying services. Before joining Baker, Matt was an Innovation Director for Redleaf Group, a Venture Capital/Operating Company focused on Information Security, Supply Chain, Network and Mobility Solutions. While at Redleaf, Matt managed technical due diligence for seed-stage investments and coordinated relationships between Redleaf and their partner companies after investment. Prior to Redleaf, Matt was CIO of GZA GeoEnvironmental Technologies, a Boston-based engineering firm, and operations manager for their Internet start-up division that focused on web-technologies for health and safety and manufacturing metrics. Matt is current board member and past Chairman of the Board for the Botanic Garden of Western Pennsylvania, a board member of the Pittsburgh History and Landmarks Foundation (PHLF), and a former member of the Information Sciences and Technology Advisory Board for the Pennsylvania State University Beaver. Matt is also a former Vice President of the Pittsburgh Chapter of the Association of Internet Professionals and former Vice President of the Board of Trustees for Baker Combined Charity of Pennsylvania.

Posted on December 15, 2006, in CNC. Bookmark the permalink. Comments Off.

Comments are closed.

Follow

Get every new post delivered to your Inbox.

Join 109 other followers